The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
This great article which follows in relation to Installing A Bathtub is absolutely attention-grabbing. Don't miss out on it.
Installing a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging task. If the old tub is readily easily accessible, the task can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as position the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have certified yourself for the work and fit trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to consider using one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This write-up will help you install a new bathtub in your washroom if you have currently gotten a new bathtub and do not need to alter the arrangement of your previous supply of water pipes.
Your devices as well as product list need to make up the following:
Preparing for the Installation
First of all, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic because of the limited accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bathtub up until the level checks out degree.
To install faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water as well as check all joints and brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally inspect the overflow outlet and also the regular outlet for leakages.
Finally, fix the bath paneling as described in the producer's user's manual. Tiling and also securing around the tub ought to wait till the tub has been utilized at least once as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in area between the faucet and the sink. Protect the faucet in position with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, resulting in problems with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can split relatively very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about Installing A Bathtub, I assumed sharing that blog post was important. I beg you take a moment to promote this write-up if you enjoyed reading it. Thank you so much for going through it.
Get it sorted! Report this page